Migration of unstructured DTP maps
Open OCAD file
Open crete-emty.ocd file. The file is located in the training data in the directory crete_ocad.
Set Map Scale
Set scale to 1:100 000 (Map -> Set Scale and Coordinate System).
-> OK
Definition of a Symbol Set
In the open OCAD file is already defines a symbol set. Exemplary in this document is the definition of the new point symbol Point of interest described.
Open scanned legend as background map
Open the TIFF file legende_crete.tif from the directory crete_backgroundmaps as backgroundmap (Backgroundmap -> Open).
Create New Symbol
Symbol -> New
Choose Point Symbol from New Symbol dialog box:
-> OK
Enter symbol number and symbol description. Click the button Edit:
The symbol editor is opened.
View -> Hide Show Entire Map and Show Map Grid
In the next step, the legend symbol must be placed into the origin of co-ordinates of the symbol editor (red arrow in fig):
Background Map -> Adjust (Shortcut F):
- Mouse click Point of interest in background map.
- Mouse click origin of co-ordinates from drawing area.
- Execute move with enter key.
Most of the fine-tuning is done in several adjust steps.- For fine-tuning it is recommended that the coordinate grid map show grid is shown.
Select the geometry Area and the Color 0: Pikto Orange in symbol editor:
Then just draw the symbol with the straight line mode File:StraightLineMode.JPG from the drawing tool.
-> Close smybol editor
The dialog box Point Symbol is shown again.
-> Icon
Create an Icon:
-> OK
The dialog box Point Symbol is shown again.
-> OK
Remove background map (Backgroundmap -> Manage):
-> Remove and Close the dialog
OCAD learning videos:
Import DTP map as PDF
Import PDF file ICV_crete_Mapsheet1_West_fhd.pdf from the directory crete_fh (File -> Import).
-> Open
Because it is multi-page PDF, it must specify the import side which should be imported. In this case page 2 must be imported
-> OK
View -> Show Entire Map show entire map
The import map is displayed. However the map is not georeferenced.
Open georeferenced Background Map
Open the georeferenced TIFF file kreta_osm_with_checkpoints.jpg from the directory crete_osm as background map (Backgroundmap -> Open).
Because it is a georeferenced background map, a dialog box appears with the question whether the new shift (horizontally and vertically according to the Easting and Northing) is to be used as the card-center.
-> Ok
View -> Show Entired Map show entire map
The Crete map the the georeferenced background map are shown. But the Crete map is still not correctly georeferenced.
The interactive georeferencing from the Crete map success in the next section.
Georeferenzing and Rubbersheeting
Change the View into Draft Mode (View -> Draft Mode).
In the toolbar, a bar appears with two controllers. With the upper controller (M=Map) can adjust the transparency of the map and with the lower controller (B=Background Map) can adjust the transparency of the background map.
Coarse adjustment using Affine transformation
In a first step, the imported map was fitted coarse with an affine transformation in the georeferenced background map (Map -> Transform -> Afine).
- Mouse click into the map.
- Mouse click on the appropriate point on the background map.
- Execute transformation with enter key.
At the affine transformtaion the maximum of 12 reference points can be defined, by repeating step 1 and 2 until the transformation is triggered by the enter button.
Fine adjustment with Rubbersheeting
In the secont step the map fitted as exactly as possible with rubbersheeting transformation on the georeferenced background map (Map -> Transform -> Rubbersheeting)
This function is only available from OCAD version 10.2.4
OCAD learning videos:
First the rubbersheeting perimeter must be determined (Define -> Draw rubbersheeting perimeter on map)
Parimeter is displayed as a blue frame in the drawing area:
When a parimeter is defined, rubbersheeting points can be added interactively or from loaded from a file.
Add rubbersheeting points interactive:
- Mouse click into the map.
- Mouse click on the appropriate point on the background map.
Rubbersheeting points are shown with a red and green crosshair and a blue connection line. In the transformation, the objects moved from the red to the green dot.
Depending on the needs the points can be deactivated, removed or saved. The deactivation is done by mouse click on the first column in the table. Unused points are shown gray in the drawing area.
Execute the transformation by clicking the Transform button.
If the result is satisfactory, the dialogue can be closed.
Otherwise there are the following possibilities:
- Undo the transformation an optimize rubbersheeting points (add, deactivate, delete)
- Use the result as a starting point for further transformation with new points.
Transform PDF XYZ in OCAD objects
Automatic conversion
can translate the functional level with the importieretn objects because of their affiliation will be converted automatically into layer objects with the appropriate symbol With the function Convert Imported Layers to Symbols (Map -> Convert Imported Layers to Symbols) imported PDF XYZ can be converted